Home > Winsock Error > Winsock Error 10060

Winsock Error 10060

Contents

Although the Mini Remote Control program only requires a single TCP port (default is TCP 6129) for communication with the MRC Client Agent on the remote machine, other ports & protocols In most cases, the default Winsock that comes with your OS is appropriate. WinServer2008 R2 by S. WSAENETDOWN (10050) Network is down A socket operation encountered a dead network. Check This Out

If you face any problem after reading this article then you can share your doubts by leaving a comment below in the comment box. This error may appear when user is using proxy service on the web browser and the connection setting do not allow to give enough time for loading up the web page, At least one QoS reserve has arrived. This can also result from connect, sendto, WSAConnect, WSAJoinLeaf, or WSASendTo when the remote address or port is not valid for a remote computer (for example, address or port 0).

Winsock Error 10060 Exchange 2013

I will recommend you to keep 180 or more. Another reason is that the host name is incorrect. For information, see the Handling Winsock Errors topic. This is what occurs in Berkeley Sockets.

  1. Some implementations also return this error if sendto is called on a connected SOCK_DGRAM socket (for SOCK_STREAM sockets, the to parameter in sendto is ignored) although other implementations treat this as
  2. Tue 2015-09-01 11:11:31: [6314:2] Sending to [208.118.**.**] Tue 2015-09-01 11:12:28: [6314:2] * Winsock Error 10054 Tue 2015-09-01 11:12:28: [6314:2] Error writing to socket Tue 2015-09-01 11:12:28: [6314:2] Socket connection closed by
  3. But before you get started make sure to create a backup of your registry files.
  4. If you used a hostname, did it resolve to the correct address?
  5. A reserved policy element was found in the QoS provider-specific buffer.   Requirements Header Winsock2.h; Winerror.h See also Error Codes - errno, h_errno and WSAGetLastError Handling Winsock Errors FormatMessage WSAGetLastError  
  6. Returned when a system call that should never fail does fail.
  7. If the hostname resolution uses a local hosttable, it's possible you resolved to an old obsolete address.
  8. Any other type of operation might also return this error—for example, setsockopt setting SO_KEEPALIVE if the connection has been reset.
  9. Do you know that this error occurs when you are trying to connect through your web pages.
  10. otherwise SMTP is working fine.  For more information kindly see the logs.

WSAEWOULDBLOCK 10035 Resource temporarily unavailable. Blocking on outbound connections is not typically done in Firewalls because then basically nothing would work. A retry at some time later may be successful. Winsock Error 10061 WSAEWOULDBLOCK (10035) Operation would blockThis is a temporary condition and later calls to the same routine may complete normally.

WSAEHOSTUNREACH 10065 No route to host. For example, the ARPA Internet UDP protocol cannot be specified with a socket type of SOCK_STREAM. WSAEPFNOSUPPORT 10046 Protocol family not supported. http://help.globalscape.com/help/cuteftp8/Socket_errors_10060_10061_10064_10065.htm WinSock description: The 'address' it refers to is the remote socket name (protocol, port and address).

Need Help? 10060 Socket Error In this case, the WSAEBADF error might mean the same as a WSAENOTSOCK error. Ian 1 Poblano OP S. WSAEPROVIDERFAILEDINIT 10106 Service provider failed to initialize.

How To Fix Error Code 10060

Ran out of disk quota. check this link right here now Please keep in mind that Winsock Errors are Microsoft Windows Sockets (TCP) errors, not DameWare error, and typically when a Winsock 10060 error is reported it's typically either due to an Winsock Error 10060 Exchange 2013 However, because a BSD socket is equivalent to a file handle, some Windows Sockets platforms provide some file handle and socket equivalency. Error Code 10060 Socket Connection Failed So, keep reading this article and find out more information about Socket error 10060.

In some instances, it also refers to the current state of the socket—for instance, calling accept on a socket that is not listening. his comment is here WSAEBADE (10009) Bad file numberA file descriptor argument was out of range, referred to no open file, or a read (write) request was made to a file that was only open The system detected an invalid pointer address in attempting to use a pointer argument of a call. Return code/valueDescription WSA_INVALID_HANDLE 6 Specified event object handle is invalid. Winsock Error 10060 Mdaemon

This normally results from a loss of the connection on the remote socket due to a timeout or a reboot. WSAEPROTONOSUPPORT 10043 Protocol not supported. If you used a hostname, did it resolve to the correct address? this contact form Usually this occurs when a file descriptor refers to a file or socket that cannot support this operation, for example, trying to accept a connection on a datagram socket.WSAEPFNOSUPPORT (10046) Protocol

The connection has been broken due to keep-alive activity detecting a failure while the operation was in progress. Socket Error 10060 Connection Timed Out Windows 7 If you are using a host table exclusively, you'll need to update it to add the destination hostname and address. Windows Firewall for SP2 or Vista, etc..) are properly configured to allow the necessary traffic to pass through.

For example, you cannot use the ARPA Internet UDP protocol with type SOCK_STREAM.

WSAELOOP 10062 Cannot translate name. This would have to be done either on the remote machine itself, or on the remote machine's defined Gateway. (see attached diagram) Lastly, if nothing else above resolves your issues, you Noman Jafar Sep 1, 2015 at 6:19 UTC #ACE: These error comes out only with few random domains. Winsock 10060 Remember meLog InCancelBy signing up or using the Techwalla services you agree to the Techwalla Terms of Use and Privacy PolicySign UpLog InCreate an account and join the conversation!

So you would have to make sure this VPN range of assigned addresses are also properly configured in the Windows Firewall on these remote machines as well (under the Scope settings An invalid QoS provider-specific buffer. Hope, you have liked this article. http://isusaa.org/winsock-error/winsock-error-code-of-10060.php Please check the URL to ensure that the path is correct.

Please see the following knowledgebase article for more information: Using DameWare Development Products in Conjunction with XP Service Pack 2 Also, if you are currently using version 6.x of the software, An invalid QoS filter type was used. The protocol family has not been configured into the system or no implementation for it exists. It means that there is a blocking operation outstanding.It is also possible that Winsock might return this error after an application calls connect a second time on a non-blocking socket while

Step 5. This normally results if the peer application on the remote host is suddenly stopped, the host is rebooted, the host or remote network interface is disabled, or the remote host uses User suggestions: There may be too many Winsock applications running simultaneously, but this is unlikely since most network systems have many socket handles available. This error is returned if an incorrect protocol is explicitly requested in the socket call, or if an address of the wrong family is used for a socket, for example, in